manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию станции

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 129

Checking the clutch actuator

If the clutch is replaced, measure the length of the

clutch control rod in order to use the correct rod.

Measure as follows:

•

Fit the new clutch on the crankshaft.

•

Fit the clutch control bowl in the gear-

box.

•

Fit the gearbox on the engine block.

•

Fit the tool in the gearbox to determine

the clutch control rod length.

•

Measure rod protrusion using a depth

gauge (see picture).

•

According to the value found, select

the correct rod based on the following

table:

Specific tooling

020678Y

 

Tool for clutch rod checking

CLUTCH CONTROL ROD SELECTION

Specification

Desc./Quantity

Protrusion: 9.8 - 11.2 mm (0.386 - 0.441 in)

Clutch control rod length (code 976593) = 183 mm (7.205 in)

Protrusion: 8.3 - 9.7 mm (0.327 - 0.382 in)

Clutch control rod length (code 976594) = 184.5 mm (7.264 in)

Protrusion: 6.8 - 8.2 mm (0.268 - 0.323 in)

Clutch control rod length (code 976595) = 186 mm (7.323 in)

Protrusion: 5.3 - 6.7 mm (0.209 - 0.264 in)

Clutch control rod length (code 976596) = 187.5 mm (7.382 in)

Assembling the clutch

•

Lock crankshaft rotation with the

crankpin facing upwards.

•

Place the clutch disc with the reference

facing upwards.

•

Fasten the clutch disc on the crank-

shaft with the six screws, Loctite 243

and the belleville springs.

Stelvio 1200 NTX ABS

Engine

ENG - 129

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды