manualshive.com logo in svg

MOTO GUZZI Stelvio 1200 NTX, Руководство по обслуживанию станции

Поделиться
Скачать
MOTO GUZZI Stelvio 1200 NTX Скачать руководство пользователя страница 166

PAY ATTENTION TO CRANKSHAFT ROTATION WHEN ONLY THE CONNECTING RODS ARE
FITTED BECAUSE IT COULD HIT THE TWO LUBRICATION JETS INSIDE THE CRANKCASE.

Installing the crankshaft

•

Fit the shim washer inside the crank-

case with the chamfered side facing

the generator side.

•

Lubricate the crankshaft bushing on

the crankcase, generator side.

•

Use the sealing ring fitting tool on the flywheel-side flange to fit the sealing ring on the flange.

Specific tooling

19.92.71.00

 

Tool to fit the sealing ring on the flywheel-side flange

•

Fit a new gasket between the crankcase and the crankshaft flange, flywheel side.

•

Fit the crankshaft on the crankcase,

flywheel side.

•

Mark the crankshaft on the flywheel

side with the crankpin facing upwards.

•

Place the suitable sealing ring centring

tool on the crankshaft.

Specific tooling

12.91.20.00

 

Tool to fit the flywheel-side flange

together with sealing ring on the crankshaft

Engine

Stelvio 1200 NTX ABS

ENG - 166

Revente Interdite - Revendita Vietata - Resaling Forbiden - Wiederverkauf Verboten

Содержание Stelvio 1200 NTX



































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды