manualshive.com logo in svg

mori seiki NZ-S1500, Руководство по эксплуатации

Поделиться
Скачать
mori seiki NZ-S1500 Скачать руководство пользователя страница 197

B-46          MANUAL OPERATION

7)

Step on the footswitch to set the chuck in the 
clamped state.

Page B-32 (7-3)

The STATUS indicator 

[CHCL]

 is lit.

8)

Set the spindle speed to the minimum value (1% of 
the maximum spindle speed) by pressing the 

spindle speed setting switch 

 (decrease) and 

the 

 (STOP) switch at the same time.

The maximum rotary tool spindle speed varies 
depending on the machine model and 
specifications.  Refer to the MAINTENANCE 
INFORMATION for the maximum rotary tool 
spindle speed of your machine.

WARNING

Before starting the rotary tool spindle 
in manual operation, set the lowest 
available spindle speed using the 

spindle speed setting switch

 

 

(decrease) and the

 

 

(STOP) 

switch.  After starting the spindle, 
increase the spindle speed to the 
required speed gradually.
When stopping the rotary tool 
spindle, first lower the spindle speed 
and then stop it.
If the rotary tool spindle is started at 
the high speed setting, the rotary tool 
could fly out, causing serious injuries 
or damage to the machine.

X

Z

MRDY

TRCL

CHCL

ERR

NOR

REV

SPJ

STOP

%

SPINDLE OVERRIDE

Содержание NZ-S1500





































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды