manualshive.com logo in svg

mori seiki NZ-S1500, Руководство по эксплуатации

Поделиться
Скачать
mori seiki NZ-S1500 Скачать руководство пользователя страница 133

OPERATION PANELS       A-49

5-18

Tailstock Spindle Switches (Tailstock Specification) 

 

 

 

 

 

 

 

The tailstock switches are used to manually extend and 
retract the tailstock spindle.

Tailstock spindle cannot be extended or retracted 
when the spindle (rotary tool spindle) is rotating 
and the turret is being indexed.

The tailstock spindle interlock function becomes effective when the 

 (TSO) or 

 (TSINC) switch is pressed.

Switch

Function

When this switch is pressed, the tailstock spindle moves out and the indicator in 
the switch is lit.

When this switch is pressed, the tailstock spindle moves in and the indicator in 
the switch is lit.

The tailstock spindle extends from the tailstock body while this switch is held 
down.

Releasing this switch stops the tailstock spindle.
The indicator in the switch is lit while this switch is pressed.

After positioning of the tailstock spindle in the inching operation, the 
cycle start of memory (tape) operation is impossible due to the tailstock 
spindle interlock function.

TSI

TSO

TSINC

NOTE

TSO

TSI

TSINC

NOTE

Содержание NZ-S1500





































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды