Monessen Hearth KSTDV500 Скачать руководство пользователя | Manualshive

Страница: 35 / 52

background image

73D4125

35

KSTDV Series Gas Fireplace

loG placeMenT

loG placeMenT

1. From the back side of the unit (with the

controls on your left) and holding log #1
in your left hand with the widest end of the
log away from you, place the log over the
pilot, making sure to locate notches in log
over the first tine from left on the near side
and the first two tines from the left on the
front side of the unit.

LG726
KSTDV log 1

Log #1

LG726

LG727
KSTDV log 2

Log #2

LG727

2. While holding log #2 in your right hand

with the wide end of the log toward you
and the flat edge on the bottom right,
place the log over the right end of all three
burners, making sure to align the notches
in the log with the first tine from the right
on both the front and the rear grates.

LG728
KSTDV log 3

Log #3

LG728

3. Hold log #3 with the fat end to the right

and the narrow end to your left.  Place
the  log  over  the  key  on  the  top  of  log
#2 closest to you making sure to align
the  bump  on  the  narrow  end  against
the inside end of the second tine from
the  left.  Position  log  with  the  inside
face  of  the  log  perpendicular  to  the
middle burner. There will be a slight gap
between the left end of the log and log
#1 (about 3/8 inch.)

Figure 47

Figure 48

Figure 49

«
...
33
34
35
36
37
...
»

Содержание KSTDV500





















































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500

Бренд: Napoleon Страницы: 48

Бренд: PSF Страницы: 2

UNI G CHIMNEY 06

Бренд: UNIPRODO Страницы: 11

Бренд: HAMPTONBAY Страницы: 30

Бренд: Continental Fireplaces Страницы: 52

Бренд: Napoleon Страницы: 2

Бренд: UBERHAUS DESIGN Страницы: 13

Бренд: Desa Страницы: 2

Бренд: Astria Страницы: 24

Бренд: Dimplex Страницы: 13

Бренд: barbas Страницы: 84

Бренд: Teamson Home Страницы: 16

VECTRON GL 05.1000 DUO PLUS

Бренд: elco Страницы: 52

Бренд: Heat&Glo Страницы: 65

Бренд: Woodbridge Fireplace Inc Страницы: 36

ECOFIRE VIVIENNE

Бренд: Palazzetti Страницы: 148

Isokern Maximus Linear 82L48ST

Бренд: EarthCore Страницы: 69

Бренд: Majestic Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды