Monessen Hearth KSTDV500 Скачать руководство пользователя | Manualshive

Страница: 5 / 52

background image

73D4125

5

KSTDV Series Gas Fireplace

proDucT FeaTureS

proDucT SpecIFIcaTIonS

•

This appliance has been certified for use with either

natural or propane gas. See appropriate data plates.

•

This appliance is not for use with solid fuels.

•

The appliance is approved for bedroom or bedsitting

room installations.

•

The appliance must be installed in accordance with local

codes if any. If none exist use the current installation
code. ANSI Z223.1/NFPA 54 in the USA, CSA B149 in
Canada.

•

This appliance is mobile home approved.

•

The appliance must be properly connected to a venting

system.

•

The appliance is not approved for closet or recessed

installations.

GaS preSSureS

hIGh eleVaTIonS

Input ratings are shown in BTU per hour and are certified
without deration for elevations up to 4,500 feet (1,370
m) above sea level.
For  elevations  above  4,500  feet  (1,370  m)  in  USA,
installations  must  be  in  accordance  with  the  current
ANSI Z223.1/NFPA 54 and/or local codes having juris-
diction.
In Canada, please consult provincial and/or local authori-
ties  having  jurisdiction  for  installations  at  elevations
above 4,500 feet (1,370 m).

Natural

Propane (LP)

Inlet Minimum

4.5” w.c.

11.0” w.c.

Inlet Maximum

10.5” w.c.

13.0” w.c.

Manifold Pressure

3.5” w.c.

10.0” w.c.

GaS SpecIFIcaTIonS & orIFIce SIZe

orifice Size

Model

Fuel

Front (2)

Middle

KSTDV500 Nat.

#46

#29

KSTDV500 LP

#56

#50

Figure 1 -
KSTDV Controls

FP2543

FP2543
kstdv controls

Control Box

Gas Valve

Command
Center

Btu/hr Input

Max.

Min.

Front

Model

Fuel all Burners all Burners

Burners

only

KSTDV500 Nat.

56,000

37,000

30,000

KSTDV500

LP

56,000

44,000

27,000

«
...
3
4
5
6
7
...
»

Содержание KSTDV500





















































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500

Бренд: Napoleon Страницы: 56

Бренд: Nectre Fireplaces Страницы: 6

FireBrick qvi25fb

Бренд: Quadra-Fire Страницы: 23

EXPEDITIONII-AU

Бренд: Quadra-Fire Страницы: 34

Бренд: Quadra-Fire Страницы: 12

Бренд: Quality Craft Страницы: 7

Бренд: Quadra-Fire Страницы: 39

Бренд: Quadra-Fire Страницы: 2

Бренд: Quadra-Fire Страницы: 24

2100 Millennium

Бренд: Quadra-Fire Страницы: 24

Superior Fireplaces Merit WRT2042WS

Бренд: IHP Страницы: 24

Бренд: Heatilator Страницы: 3

WALDON CTCFP60-5

Бренд: Canvas Страницы: 100

Бренд: Napoleon Страницы: 40

Garden Lights 26371

Бренд: Landmann Страницы: 4

Бренд: Desa Страницы: 32

Бренд: Travis Industries Страницы: 9

Бренд: HAMPTON BAY Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды