Monessen Hearth KSTDV500 Скачать руководство пользователя | Manualshive

Страница: 32 / 52

background image

32

73D4125

KSTDV Series Gas Fireplace

reMoTe conTrol operaTIon

aux control (rear Burner Shut Down)

Figure 38

1. Press AUX button once to turn rear burner off. AUX shows on the LCD.
2. Press AUX button again to turn on rear burner. AUX icon disappears.

°F

FP2149
AUX display
12/08

AUX

FP2149

Figure 38 -
AUX Display

low Battery Detection

Figure 39

1. Battery voltage is checked once a minute. When the battery voltage drops to a certain

level, the low-battery icon will display on LCD, and the transmitter will turn off the fire-
place. The transmitter will not function anymore until fresh batteries are installed.

2. When the batteries are low, the LCD displays a low battery indicator. The low battery

indicator will be displayed in any mode.

3. The transmitter will not operate with low batteries. Change the batteries before the

batteries are too weak for normal operation. Turn the unit OFF before replacing batter-
ies.

°F

FP2150
low battery display
12/08

FP2150

Figure 39 -
Low Battery Display

child-proof protection

Figure 40

1. Press and hold the ON and OFF buttons simultaneously for three (3) seconds to enter

child proof mode. Figure K

2. The transmitter will not send a signal again until the childproof mode is deactivated by

pressing the ON and OFF buttons simultaneously for three (3) seconds to exit child proof
mode and the Childproof indicator disappears from LCD.

°F

FP2151
no child display
12/08

FP2151

Figure 40 -
Child Protection Display

Transmitter Thermal Shutdown

Figure 41

1. If transmitter measures a room temperature exceeding 99° F, the LCD will display "HI"

and the transmitter will turn off the fireplace.

2. Transmitter will not function until the room temperature has dropped below 99° F. If

transmitter measures a room temperature less than 40° F, the LCD will display "LO"
and NO SIGNAL will be sent to turn on the fireplace.

FP2152
thermal shutdown display
12/08

FP2152

Figure 41 -
Thermal Shutdown Display

«
...
30
31
32
33
34
...
»

Содержание KSTDV500





















































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500

Бренд: Superior Страницы: 12

emifocus hublot dv

Бренд: Focus Страницы: 8

Бренд: Kemlan Страницы: 23

Бренд: Valor Страницы: 48

Argon Built 3 Sided

Бренд: Stanley Страницы: 26

Бренд: barbas Страницы: 100

Бренд: Vantage Hearth Страницы: 40

Бренд: Napoleon Страницы: 2

Бренд: Pacific energy Страницы: 24

Бренд: Pur Line Страницы: 12

mantels & surrounds Kenwood Flush

Бренд: Fireside Страницы: 6

Бренд: Ekofires Страницы: 20

Бренд: EdilKamin Страницы: 19

Бренд: komodo Страницы: 32

Бренд: Spatherm Страницы: 24

Бренд: Spartherm Страницы: 28

Contura C856W Style

Бренд: Nibe Страницы: 20

Бренд: Nouveau Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды