Monessen Hearth KSTDV500 Скачать руководство пользователя | Manualshive

Страница: 11 / 52

background image

73D4125

11

KSTDV Series Gas Fireplace

VenTInG InSTallaTIon

InSTallaTIon precauTIonS

Consult  local  building  codes  before  beginning  the
installation.  The  installer  must  make  sure  to  select  the
proper vent system for installation. Before installing vent
kit, the installer must read this fireplace manual and vent
kit instructions.
Only a qualified installer/service person should install the
venting  system.  The  installer  must  follow  these  safety
rules:

•

Wear gloves and safety glasses for protection.

•

Use extreme caution when using ladders or when on

rooftops.

•

Be aware of electrical wiring locations in walls and ceil-
ings.

The following actions will void the warranty on your vent-
ing system:

•

Installation of any damaged venting component.

•

Unauthorized modification of the venting system.

•

Installation of any component part not manufactured or
approved by MHSC

•

Installation other than permitted by these instructions.

w

arn

In

G

horizontal sections of this vent system require a minimum of 3" clearances
to combustibles at the top of the flue and 1" clearance at the sides and
bottom

until the flue penetrates the outside wall.

a minimum 1" clearance

all around the flue is acceptable at this point of penetration.
Vertical sections of this vent system require a minimum of 2" clearance to
combustibles at the top of the unit directly above the stand-off. a minimum
of 1" clearance all around the flue is acceptable thereafter.

This fireplace must be vented to the outside. The venting system must
neVer be attached to a chimney serving a separate solid fuel burning
appliance. each gas appliance must use a separate vent system. Do not
use common vent systems.

w

arn

In

G

read all instructions completely and thoroughly before attempting
installation. Failure to do so could result in serious injury, property damage
or loss of life. operation of improperly installed and maintained venting
system could result in serious injury, property damage or loss of life.

w

arn

In

G

Failure to follow these instructions will
void the warranty.

no

TI

ce

*3”

**1”

**1”

FP2567
KSTDV vent clearances

24”

(610 mm)

72”

(1829 mm)

Figure 7 -
Combustible Clearances for Vent Pipe

* A minimum of 3" clearance to the top is
required along horizontal length until flue pipe
penetrates outside wall.
** A minimum 1" clearance to combustibles
permitted all around flue at outside wall

FP2567

«
...
9
10
11
12
13
...
»

Содержание KSTDV500





















































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500

Бренд: Yunca Gas Страницы: 19

Бренд: Valor Fires Страницы: 56

Бренд: Valor Fires Страницы: 56

Бренд: Valor Страницы: 72

Бренд: Valor Страницы: 38

Бренд: Vermont Castings Страницы: 24

Бренд: RAIS Страницы: 108

NC4314R-42-Base

Бренд: PATIO HQ Страницы: 16

Бренд: Living Страницы: 14

Бренд: Fire Sense Страницы: 7

Бренд: Fire dept Страницы: 18

Comfort Glow CGEFP33PR

Бренд: Desa Страницы: 38

ELECTRIFLAME XD Mk2 B-1005344

Бренд: Celsi Страницы: 12

Бренд: M Design Страницы: 13

Бренд: Heatilator Страницы: 24

Бренд: Lennox Hearth Products Страницы: 2

Бренд: Astria Страницы: 24

Бренд: Quadra-Fire Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды