Monessen Hearth KSTDV500 Скачать руководство пользователя | Manualshive

Страница: 20 / 52

background image

20

73D4125

KSTDV Series Gas Fireplace

FIreplace InSTallaTIon

checK GaS Type

Use proper gas type for the fireplace you are installing. If you have conflicting gas type, do not install
fireplace. See dealer where you purchased the fireplace for proper fireplace according to your gas
type.

InSTallInG GaS pIpInG To FIreplace locaTIon

When using copper or flex connectors use only fittings
approved for gas connections. The gas control inlet is
3/8" NPT.

w

arn

In

G

a qualified installer or service person must
connect appliance to gas supply. Follow
all local codes.

cau

TI

on

For  propane/lp  units,  never  connect
fireplace  directly  to  the  propane/lp
supply.  This  burner  system  requires  an
external  regulator  (not  supplied).  Install
the external regulator between the burner
system and propane/lp supply.

InSTallaTIon ITeMS neeDeD

Before installing fireplace and burner system, make sure you have the items listed below.

•

External regulator

•

Piping (check local codes)

•

Sealant (resistant to propane/LP gas)

(supplied by installer)

•

Test gauge connection*

• Sediment trap (recommended)

•

Equipment shutoff valve*

•

Tee joint

•

Pipe wrench

•

approved flexible gas line with gas connector (if allowed by local codes — not provided)

*

A CSA design-certified equipment shutoff valve with 1/8" NPT tap is an acceptable alternative to test gauge
connection. Purchase the CSA design-certified equipment shutoff valve from your dealer.

For propane/LP connections only, the installer must supply an external regulator. The external regulator will reduce
incoming gas pressure. You must reduce incoming gas pressure to between 11 and 13 inches of water. If you do not
reduce incoming gas pressure, burner system regulator damage could occur. Install external regulator with the vent
pointing down as shown in

Figure 23.

Pointing the vent down protects it from freezing rain or sleet.

cau

TI

on

use only new black iron or steel pipe.
Internally tinned copper or copper tubing
can be used per national Fuel code, Section
2.6.3, providing gas meets hydrogen sulfide
limits, and where permitted by local codes.
Gas piping system must be sized to provide
minimum inlet pressure (listed on data
plate) at the maximum flow rate (BTu/hr).
undue pressure loss will occur if the pipe
is too small.

FP1977
external regulator

External
Regulator

100 gal. (min)
Propane/LP
Supply Tank

Vent Pointing
Down

Figure 23 -
External Regulator with Vent Pointing Down
(Propane/LP Only)

FP1977

w

arn

In

G

external regulators may be necessary for
natural gas. one- or two-pound systems
will damage this appliance and may cause
fire hazard.

«
...
18
19
20
21
22
...
»

Содержание KSTDV500





















































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500

Бренд: Cadet Страницы: 13

Бренд: Napoleon Страницы: 4

Бренд: RealFlame Страницы: 14

Бренд: Vantage Hearth Страницы: 40

Бренд: Coopers of Stortford Страницы: 2

Бренд: pleasant hearth Страницы: 2

Бренд: Vanguard Страницы: 38

Бренд: Kingsman Страницы: 59

Бренд: Heat & Glo Страницы: 2

FireBrick Gas Insert ADI-ZCFB-S

Бренд: Heatilator Страницы: 2

Бренд: Valor Страницы: 16

Wall Mantel with Base and Trim WD26CPA

Бренд: Desa Страницы: 4

Бренд: Pur Line Страницы: 52

Бренд: Majestic Страницы: 24

Бренд: HAMPTON BAY Страницы: 12

Бренд: Laminvale Страницы: 9

Бренд: Element4 Страницы: 64

Бренд: Napoleon Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды