Monessen Hearth KSTDV500 Скачать руководство пользователя | Manualshive

Страница: 18 / 52

background image

18

73D4125

KSTDV Series Gas Fireplace

InSTallaTIon For VerTIcal TerMIna-
TIon

1. Determine the route your vertical venting will take. If

ceiling joist, roof rafters or other framing will obstruct
the venting system, consider an offset.

Refer to Figure

19

to avoid cutting load bearing members.

For optimal flame appearance, a restrictor disk is necessary
on straight vertical runs of 10' of more.

•

Runs may not incorporate elbows.

•

The disk is part number 56D3027 and is included in
installation manual packet.

•

Drop the disk into a 5" inner collar before installing the
first section of flue or install at the last section before
installing the termination. Also disk can be installed
from inside the firebox into the 5" inner collar.

•

An additional disk may be installed on runs of 35' or
more. Rotate disks perpendicular to each other.

noTe:

Pay special attention to these installation instructions

for required clearances (air space) to combustibles when
passing through ceilings, walls, roofs, enclosures, attic
rafters, etc. Do not pack air spaces with insulation. Also
note maximum vertical rise of the venting system and any
maximum horizontal offset limitations. Offsets must fall

VenTInG InSTallaTIon

FP1969
offset w/ wallstrap

Figure 19 -
Offset with Wall Strap and 45° Elbows

Roof Flashing

Wall Strap

45° Elbows

Ceiling Firestop

FP1669

within the parameters shown in

Figures 20 and 21

.

2. Set fireplace in desired location. Drop a line plumb down

from the ceiling to the position of the flue exit. Mark the
center point where the vent will penetrate the ceiling.
Drill a small locating hole a this point.

Drop a plumb line from the inside of the roof to the ceiling

locating hole in the ceiling. Mark the center point where
the vent will penetrate the roof. Drill a small locating hole
at this point.

FlaT ceIlInG InSTallaTIon

1. Cut a 10

Z\x

" (241 mm) square hole in the ceiling using

the locating hole as a center point The opening should
be framed to 10

Z\x

"x10

Z\x

" (241 mm x 241 mm) inside

dimensions as shown in

Figure 21

using framing lumber

the same size as the ceiling joist. If the area above the
ceiling is an insulated ceiling or a room, nail firestop from
the top side. This prevents loose insulation from falling
into the required clearance space.

Figure 20.

Otherwise,

install firestop below the framed hole.

Figure 21

FP1969
firestop w room above

10

1

/

2

"

10

1

/

2

"

FP1970
firestop no room

Figure 20 -
If Area Above is a Room, Install Firestop above
Framed Hole as Shown

Figure 21 -
If Area Above is Not a Room, Install Firestop above
Framed Hole as Shown

Firestop

Nails

Nails

Firestop

FP1970

«
...
16
17
18
19
20
...
»

Содержание KSTDV500





















































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500

Бренд: Magiglo Страницы: 48

Бренд: HAMPTON BAY Страницы: 18

Бренд: Martin Страницы: 36

Smart Bell 65/55 MF

Бренд: Bellfires Страницы: 48

Бренд: IHP Страницы: 4

GOLDEN DAWN TX 93531

Бренд: Leigh Country Страницы: 2

Бренд: Gas Technologies Страницы: 31

Бренд: Uniflame Страницы: 2

Бренд: Scott Living Страницы: 27

Бренд: Napoleon Страницы: 4

Bronson BRON5151-K

Бренд: Outdoor GreatRoom Company Страницы: 16

Бренд: HAMPTON BAY Страницы: 40

Бренд: Fire Sense Страницы: 5

Бренд: ELEMENTI Страницы: 60

Бренд: Archgard Страницы: 42

Бренд: Majestic Страницы: 44

Slimfocus pivotant

Бренд: Focus Страницы: 11

Бренд: IHP Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды