Monessen Hearth KSTDV500 Скачать руководство пользователя | Manualshive

Страница: 21 / 52

background image

73D4125

21

KSTDV Series Gas Fireplace

FIreplace InSTallaTIon

noTe :

The gas line connection may be made using 1/2" rigid tubing or an approved flex connector.

Since some municipalities have additional local codes it is always best to consult your local authorities
and the current edition of the National Fuel Gas Code ANSI.Z223.1, NFPA54. In Canada CSA-B149 (1
or 2) Installation Code.
A listed manual shutoff valve must be installed upstream of
the appliance. Union tee and plugged 1/8" NPT pressure
tapping point should be installed upstream of the appliance.

Figure 24

IMporTanT:

Install main gas valve (equipment shutoff valve)

in an accessible location. The main gas valve is for turning on
or shutting off the gas to the fireplace.

Check your building codes for any special requirements for locating equipment shutoff valve to fire-
places.
Apply pipe joint sealant lightly to male threads. This will prevent excess sealant from going into pipe.
Excess sealant in pipe could result in clogged burner system valves.
We recommend that you install a sediment trap/drip leg in supply line as shown in

Figure 24

. Locate

sediment trap/drip leg where it is within reach for cleaning. Install in piping system between fuel supply
and burner system. Locate sediment trap/drip leg where trapped matter is not likely to freeze. A sediment
trap traps moisture and contaminants. This keeps them from going into the burner system gas controls.
If sediment trap/drip leg is not installed or is installed wrong, burner system may not run properly.

w

arn

In

G

only persons licensed to work with gas
piping may make the necessary gas
connections to this appliance.

cau

TI

on

a manual shutoff valve must be installed
upstream of the appliance. union tee
and plugged 1/8" npT pressure tapping
point should be installed upstream of the
appliance.

See Figure 38.

cau

TI

on

use pipe joint sealant that is resistant to
liquid petroleum (lp) gas.

3" Minimum

FP1978
gas connection

Pipe Nipple

Cap

Figure 24 -
Gas Connection

Tee Joint

Approved Flexible
Gas Line

CSA Design-Certified Equipment Shutoff Valve
with 1/8" NPT Tap*

Sediment Trap/Drip Leg

natural Gas

From Gas Meter

(4.0" w.c. to 10.5" w.c. Pressure)

propane/lp

From External Regulator

(11" w.c. to 13" w.c. Pressure)

InSTall GaS Supply lIne

«
...
19
20
21
22
23
...
»

Содержание KSTDV500





















































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500

CLASSIC BELL SMALL 3 PF

Бренд: Bellfires Страницы: 88

CROSSOVER CO10-101-M

Бренд: Magma Страницы: 18

Бренд: Valor Страницы: 60

Бренд: Heatilator Страницы: 32

Бренд: NARVI Страницы: 7

MPS-34 Minneapolis XL

Бренд: kozy heat Страницы: 38

L-OF083PST-2 Bel Aire

Бренд: Sunjoy Страницы: 4

Бренд: ELEMENTI Страницы: 60

Бренд: Majestic Страницы: 20

Бренд: Outfit Страницы: 37

Бренд: Paramount Fitness Страницы: 9

Бренд: Amantii Страницы: 33

Бренд: Kingsman Fireplaces Страницы: 7

Бренд: Contura Страницы: 12

Бренд: HEINZE Страницы: 2

Бренд: Lennox Hearth Products Страницы: 42

Бренд: Jocel Страницы: 22

Бренд: Char-Broil Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды