Monessen Hearth KSTDV500 Скачать руководство пользователя | Manualshive

Страница: 8 / 52

background image

8

73D4125

KSTDV Series Gas Fireplace

pre-InSTallaTIon InForMaTIon

FIreplace locaTIon

Plan for the installation of your appliance. This includes determining where the unit is to be installed,
the vent configuration to be used, framing and finishing details, and whether any optional accessories
(i.e. blower, wall switch, or remote control) are desired. Consult your local building code agency to
ensure compliance with local codes, including permits and inspections.
The following factors should be taken into consideration:

•

Clearance to side-wall, ceiling, woodwork, and windows. Minimum clearances to combustibles

must be maintained.

•

This fireplace may be installed along a wall, across a corner, or use an exterior chase. Refer to

Figure 3

for suggested locations.

•

Location should be out of high traffic areas and away from furniture and draperies due to heat

from appliance.

•

Never obstruct the front opening of the fireplace.

•

Do

not

install in the vicinity where gasoline or other flammable liquids may be stored.

•

Vent pipe routing. See

Venting

section found in this manual for allowable venting configura-

tions.

•

These units can be installed in a bedroom. See National Fuel Gas Code ANSI Z233.1/NFPA 54

— (current edition), the Uniform Mechanical Code — (current edition), and Local Building Codes
for specific installation requirements.

•

These units can be installed in a bathroom.

Y

D

A

B

C

E

Y

X

LU584
Locating unit
DVT38S2
3/17/04 djt

** Island (C) and Room Divider (D) installation is possible as long
as the horizontal portion of the vent system (X) does not exceed
20’ (610cm). See details in Venting Section.
* When you install your fireplace in (D) Room divider or (E) Flat
on wall corner positions (Y), a minimum of 6” (152mm) clearance
must be maintained from the perpendicular wall and the front side
edge of the fireplace.

A  Flat on wall
B  **Island
C  *Room divider
D  *Flat on wall corner
E  Chase installation
Y  6” minimum

Figure 3 -
Locate Fireplace

noTe:

For exterior wall applications, outdoor facing kit

KST500SSDK is required. In these installations, the con-
trol-side of the unit MUST face towards the interior of the
building.

«
...
6
7
8
9
10
...
»

Содержание KSTDV500





















































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500

Бренд: BCP Страницы: 16

Бренд: Jensen Страницы: 45

VECTRON GL 05.1000 DUO PLUS

Бренд: elco Страницы: 52

BEDFORD A Series

Бренд: Pacific energy Страницы: 44

Бренд: Vola Страницы: 36

Melrose Dark Cherry

Бренд: Stonegate Страницы: 17

Savannah Chat P33442G

Бренд: Paragon Casual Страницы: 15

Бренд: Design Dynamics Страницы: 44

RHAPSODY RHAP42N

Бренд: IHP Страницы: 6

Бренд: Pioneer Страницы: 16

Бренд: Nordpeis Страницы: 13

Бренд: Nordpeis Страницы: 31

Бренд: Nordpeis Страницы: 64

Бренд: Nordpeis Страницы: 24

Бренд: Nordpeis Страницы: 92

Бренд: Nordpeis Страницы: 50

CC-RIO00-100 Ronda

Бренд: Nordpeis Страницы: 48

Бренд: Nordpeis Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды