Monessen Hearth KSTDV500 Скачать руководство пользователя | Manualshive

Страница: 22 / 52

background image

22

73D4125

KSTDV Series Gas Fireplace

FP1909a
signature command valve
alternate view
8/08

1. Check gas type. The gas supply must be the same as

stated on the appliance’s rating decal. If the gas supply
is different from the fireplace,

STop!

Do not install the

appliance. Contact your dealer immediately.

2. To ease installation, a 24" (610 mm) flex line with manual

shut-off valve has been provided with on this appliance.
Install and attach 1/2" gas line onto shut-off valve.

3. After completing gas line connection, purge air from

gas line and test all gas joints from the gas meter to the
fireplace for leaks. Use a solution of 50/50 water and
soap solution or a gas sniffer.

4. To check gas pressures at valve, turn captured screw

counter clockwise 2 or 3 turns and then place tubing to
pressure gauge over test point. Turn unit to high.

Fig-

ure 25

After taking pressure reading, be sure and turn

captured screw clockwise firmly to reseal. Do not over
torque. Check test points for gas leaks.

Figure 25 -
Signature Command Valve

Pilot Adjustment
Screw

Pressure Outlet

w

arn

In

G

Do not use open flame to check for gas
leaks.

elecTrIcal wIrInG

This fireplace burner system will work without any electrical supply during power outages (battery
back-up system). Electricity is only needed to operate blower, lights and rear burn shut off.

NOTE: If installed in mobile home, fireplace must be bolted securely to floor.

w

arn

In

G

electrical  connections  should  only
be  performed  by  a  qualified,  licensed
electrician. Main power must be off when
connecting to main electrical power supply
or  performing  service. all  wiring  shall  be
in compliance with all local, city and state
codes. The appliance, when installed, must
be  electrically  grounded  in  accordance
with local codes or in the absence of local
codes,  with  the  national  electrical  code
anSI/nFpa 70 (latest edition) and canadian
electrical code, cSa c22.1.

cau

TI

on

label all wires before disconnecting when
servicing controls. wiring errors can cause
improper and dangerous operation.

Verify proper operation after servicing.

FP1909a

Pressure Inlet

SIGnaTure coMManD - checK GaS preSSure and elecTrIcal InSTallaTIon

«
...
20
21
22
23
24
...
»

Содержание KSTDV500





















































Отзывы:

Нет отзывов

Похожие инструкции для KSTDV500

Бренд: JAYLINE Страницы: 15

Бренд: Desa Страницы: 44

Бренд: Camina Страницы: 48

Бренд: Twin-Star International Страницы: 19

Бренд: Astria Страницы: 24

FireStage UVHK29RN

Бренд: Majestic fireplaces Страницы: 6

Бренд: Valor Страницы: 14

Бренд: Astria Fireplaces Страницы: 2

Бренд: Monessen Hearth Страницы: 4

Бренд: Kooper Страницы: 12

Бренд: BRW Страницы: 2

Symmetry RDV3600

Бренд: Rinnai Страницы: 20

Бренд: RAIS Страницы: 11

Бренд: HAMPTON BAY Страницы: 32

Бренд: Wamsler Страницы: 88

Бренд: Coleman Страницы: 2

Бренд: Coleman Страницы: 2

Бренд: GlammFire Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды