Mitsubishi Electric F700, Инструкция по эксплуатации

Страница: 237 / 341

228
Special operation and frequency control
<Set point input calibration>
1) Setting with terminal 2 input
1. Apply the input voltage of 0% set point setting (e.g. 0V) across terminals 2-5.
2. Enter in
C2 (Pr. 902) the frequency which should be output by the inverter at the deviation of 0% (e.g. 0Hz).
3. In C3 (Pr. 902) , set the voltage value at 0%.
4. Apply the voltage of 100% set point (e.g. 5V) to across terminals 2-5.
5. Enter in
Pr. 125 the frequency which should be output by the inverter at the deviation of 100% (e.g. 50Hz).
6. In C4 (Pr. 903) , set the voltage value at 100%.
2) Setting with
Pr. 133
When both or one of C42 (Pr.934) and C44 (Pr.935) is "9999".
For the set point, set a % converted value in the range of 0 to 100%.
When both of
C42 (Pr.934) and C44 (Pr.935)
z
"9999".
For the set point, set PID coefficient, which corresponds with 0 to 100%.
<Measured value calibration>
1) When both or one of C42 (Pr.934) and C44 (Pr.935) is "9999".
1. Apply the input current of 0% measured value (e.g. 4mA) across terminals 4-5.
2. Make calibration using
C6 (Pr. 904) .
3. Apply the input current of 100% measured value (e.g. 20mA) across terminals 4-5.
4. Make calibration using
C7 (Pr. 905) .
2) When both of
C42 (Pr.934)
and
C44 (Pr.935)
z
"9999".
1. Apply the input current of 0% measured value (e.g. 4mA) across terminals 4 and 5.
2. Set PID display value at 0% measured value (example: 15(
q
C)) to C42 (Pr.934) , and calibrate C43 (Pr.934) .
3. Apply the input current of 100% measured value (e.g. 20mA) across terminals 4 and 5.
4. Set PID display value at 100% measured value (example: 35(
q
C)) to
C44 (Pr.935)
, and calibrate
C45 (Pr.935)
.
The results of the above calibration are as shown below:
REMARKS
˜
The frequency set in
C5 (Pr. 904)
and
Pr. 126
should be the same as set in
C2 (Pr. 902)
and
Pr. 125
.
Pr.133
Setting
Pr.934,
Pr.935
Setting
Set Point Setting
Measured Value
(Terminal 4)
Manipulated Variable
9999 ——
(Terminal 2)
Other than
9999
Both or one
is 9999
(Pr.133)
Other than
9999
(Pr.133)
Set PID coefficient
corresponding with 0 to 100%.
100
0
0 5 (V)
Set point signal input
Set point
(%)
100
0
0 20
C7(Pr.905)
(mA)
Measured value
input signal
Measured
Value
(%)
4
C6(Pr.904)
60
(Pr.125)
0
C2(Pr.902)
0 100
Deviation(%)
Manipulated
Variable(Hz)
100
0
C5(Pr.904) Pr.126
Set point setting
Set point
(%)
100
0
C42(Pr.934)
C44(Pr.935)
Set point
(%)
100
0
0 20
C45(Pr.935)
(mA)
Measured value
input signal
Measured
value
(%)
4
C43(Pr.934)