Mitsubishi Electric F700, Инструкция по эксплуатации

Страница: 120 / 341

111
Function assignment of external
terminal and control
4
PA
R
A
M
E
T
E
R
S
*1 When Pr. 59 Remote function selection
z
"0", the functions of the RL, RM and RH signals change as listed above.
*2 The OH signal turns on when the relay contact "opens".
2 RH
Pr. 59 = 0 (initial value) High-speed operation command
Pr. 4 to Pr. 6, Pr. 24 to Pr. 27, Pr.
232 to Pr. 239
82
Pr. 59
z
0
*1
Remote setting (acceleration) Pr. 59 87
3 RT Second function selection Pr. 44 to Pr. 51 113
4 AU Terminal 4 input selection Pr. 267 155
5 JOG Jog operation selection Pr. 15, Pr. 16 84
6 CS
Selection of automatic restart after instantaneous power failure,
flying start Pr. 57, Pr. 58, Pr.162 to Pr.165,
Pr. 299, Pr. 611
136
Electronic bypass function
Pr. 57, Pr. 58 Pr. 135 to Pr. 139,
Pr. 159
231
7 OH External thermal relay input
*2
Pr. 9 95
8 REX 15 speed selection (combination with three speeds RL, RM, RH)
Pr. 4 to Pr. 6, Pr. 24 to Pr. 27,
Pr.232 to Pr.239
82
10 X10 Inverter operation enable signal (FR-HC, MT-HC/FR-CV connection) Pr. 30 102
11 X11 FR-HC or MT-HC connection, instantaneous power failure detection Pr. 30 102
12 X12 PU operation external interlock Pr. 79 175
13 X13 External DC injection brake operation start Pr. 11, Pr. 12 100
14 X14 PID control valid terminal
Pr. 127 to Pr. 134, Pr. 575 to Pr.
577
219
16 X16
PU-external operation switchover
(external operation when X16 turns on)
Pr. 79, Pr. 340 181
24 MRS
Output stop Pr. 17 112
Electronic bypass function
Pr. 57, Pr. 58, Pr. 135 to Pr. 139,
Pr. 159
231
25 STOP Start self-holding selection

114
37 X37 Traverse function selection Pr. 592 to Pr. 597 246
60 STF
Forward rotation command
(assigned to STF terminal
(Pr. 178)
only)

114
61 STR
Reverse rotation command
(assigned to STR terminal
(Pr. 179) only)

114
62 RES Inverter reset
 
63 PTC PTC thermistor input (assigned to AU terminal (Pr. 184) only) Pr. 9 95
64 X64 PID forward/reverse action switchover Pr. 127 to Pr. 134 219
65 X65
PU-NET operation switchover
(PU operation when X65 turns on)
Pr. 79, Pr. 340 183
66 X66
External-NET operation switchover
(NET operation when X66 turns on)
Pr. 79, Pr. 340 183
67 X67
Command source switchover
(
Pr.338 and Pr.339 commands are valid when X67 turns on)
Pr. 338, Pr. 339 184
70 X70 DC feeding operation permission Pr. 30, Pr. 70 102
71 X71 DC feeding cancel Pr. 30, Pr. 70 102
72 X72 PID integral value reset
Pr. 127 to Pr. 134, Pr. 241, Pr.
553, Pr. 554, Pr. 575 to Pr. 577,
C42 to C45
219
9999

No function
 
REMARKS
˜
Same function can be assigned to two or more terminals. In this case, the logic of terminal input is OR.
˜
The priorities of the speed commands are in order of jog > multi-speed setting (RH, RM, RL, REX) > PID (X14).
˜
When the X10 signal (FR-HC, MT-HC, FR-CV connection - inverter operation enable signal) is not set or when the PU
operation external interlock (X12) signal is not assigned at the
Pr. 79 Operation mode selection setting of "7", the MRS signal
shares this function.
˜
Same signal is used to assign multi-speeds (7 speeds) and remote setting. They cannot be set individually.
(Same signal is used since multi-speed (7 speeds) setting and remote setting are not used to set speed at the same time .)
CAUTION
˜
Changing the terminal assignment using Pr. 178 to Pr. 189 (input terminal function selection) may affect the other functions. Also
check that wiring is correct, since the terminal name and the signal function became different. Please make setting after
confirming the function of each terminal.
Setting
Signal
Name
Function Related Parameters
Refer to
Page