Mighty Mule MM560 Скачать руководство пользователя

Страница: 4 / 44

MM560 Installation Instructions

Please Read This First!

Thank you for purchasing a Mighty Mule Gate

Operator—GTO's "do-it-yourself" automatic gate

operator! When correctly installed and properly used,

your Mighty Mule Gate Operator will give you many

years of reliable service. Please read the following

information and watch the enclosed video to ensure

you have the correct system for your particular

needs. Furthermore, this manual and the DVD will

enable you to properly install your Mighty Mule Gate

Operator.

The Mighty Mule Gate Operator is designed for

installation on a pull-to-open single leaf gate (gates

that open into the property). By purchasing an push-

to-open bracket (FM143), the Mighty Mule Gate

Operator can accommodate a push-to-open single leaf

gate (gates that open out from the property). The gate

must not exceed 18 feet in length ord weigh more

than 850 pounds (please see Technical Specifications

on page 9). The Mighty Mule Gate Operator can be

used on vinyl, aluminum, chain link, farm tube, and

wrought iron gates. Use on solid surface gates is

not recommended. Solid surface gates have a high

resistance to the wind. If the wind is strong enough,

the operator will obstruct and stop.

The Mighty Mule Gate Operator accommodates

extra transmitters, digital keypads, solar panels,

push buttons, automatic gate locks, and other access

control products. These optional accessories (see the

Mighty Mule Accessory Catalog) are available at most

stores. Your store should be able to special order any

accessory not in stock. If your store cannot special

order accessories, please call the Mighty Mule Sales

Department (800-543-4283).

The Mighty Mule Gate Operator features Dual Sense

Technology™. This feature makes the gate stop and

reverse direction when it comes in contact with an

obstruction. This is factory set to the most sensitive

setting and may need to be adjusted during installation.

The Mighty Mule Gate Operator also has an adjustable

auto-close feature. After the gate reaches the fully

open position, it can be set to remain open up to 120

seconds before automatically closing. Pressing the

transmitter button at any time after the gate opens fully

will cause it to close immediately. OFF is the factory

setting; meaning the gate will stay open until you press

the transmitter (or keypad, etc.) again.

NOTE—If your application requires any of the

following:

• Swing gates longer than 18 feet or weighing

more than 850 pounds

• Slide gates

• Heavy duty or commercial uses

• Professional installation

Go to www.gtoaccess.com for a dealer or retailer near

you or call (800) 543-4283 for information about our

Linear PRO Access professional line of gate operators

and accessories. Our Sales Department will be glad to

give you the name and phone number of a Linear PRO

Access dealer near you

BEFORE YOU BEGIN TO INSTALL YOUR AUTOMATIC GATE OPERATOR:

watch the enclosed video and read these instructions carefully and completely

to become familiar with all parts and installation steps. The video is only designed as an

overview of the installation procedure. You must read the installation manual for detailed

instructions on gate operator safety and proper use of the gate operator.

Содержание MM560













































Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды

Mighty Mule MM560, Руководство по установке

Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды