Mighty Mule MM560 Скачать руководство пользователя

Страница: 14 / 44

MM560 Installation Instructions

Before You Begin

3/8” x 1-1/4” Clevis Pin (2)

RB500

Volt

7.0 A

mp M

oun

3/8” x 8” Bolt (4)

8” Nylon Cable Tie (14)

Receiver and

Control Box

Operator

Arm

Gate Bracket

Post Pivot Bracket

Post Brackets

Transformer

Warning

Sign

Closed Position

Bracket

Transmitter

Installation

Video

Battery

3/8” x 2” Bolt (1)

5/16” x 1-3/4” Bolt (1)

3/8” Washer (9)

3/8” Lock Washer (7)

5/16” Lock Washer (1)

5/16” Washer (1)

3/8” Nut (7)

5/16” Nut (1)

Hairpin Clip (2)

2” Mounting Screw (5)

KEEP CLE

AR! G

ate

may mo

ve at a

ny tim

Do not allow c

hildre

n to op

era

te g

ate or

play in gate

area.

This gate is

for vehic

les

onl

y. P

ede

stri

ans

must us

e a se

parate

tran

ce.

Moving Ga

te Can

use

Injury O

r Dea

WARNING

Installa

tion O

ver

view f

or the

...

3/8” Bushing (2)

3/8” x 3” Bolt (2)

Items Included

Gate Grounding

(recommended)

• Shorter wire (6 AWG) is better, 1 to 2 feet recommended.
• Bolt ring terminal at end of cable 4 - 6 inches above ground

level.

R4196 Kit Includes:
•  Ground Rod Clamp
•  6 AWG Wire (3 feet)
NOTE: No grounding system absolutely protects against
lightning strikes. If installed correctly, a grounding system will
help minimize damage to your gate opener.

Metal Gate

Post

6 AWG Wire

8 Foot Ground Rod

5/8” Copper Clad Steel (not included)

- available at local homecenter and hardware stores -

Ground Rod

Clamp

Содержание MM560













































Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды

Mighty Mule MM560, Руководство по установке

Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды