Mighty Mule MM560 Скачать руководство пользователя

Страница: 10 / 44

MM560 Installation Instructions

500

UL325 SERIES

E-Z GATE OPENER

1-800-543-GATE (4283)

www.mightymule.com

Warning Sign

Pedestrian Gate

Bulldog Pedestrian

Gate Lock

Vehicular Gate

(recommended, not included

)

7 foot

Important Safety Information

Warning signs alert people of automatic gate operation and are required when installing Mighty Mule Automatic

Gate Operators. A minimum of two WARNING SIGNS must be installed in the area of the gate. Each sign is to be

visible by persons located on the side of the gate on which the placard is installed.

The operator is intended for installation only on gates used for vehicles. Pedestrians must be supplied with a

separate access. The pedestrian access shall be designed to promote pedestrian usage. Locate the gate such that

persons will not come in contact with the vehicular gate during the entire path of travel of the vehicular gate.

We recommend using the GTO Bulldog Pedestrian Gate Lock (Call the GTO Sales Department at 800-543-4283)

for controlled access.

Installing Warning SIgns and Pedestrian Gates

Warning Signs

The gate operator is provided with 2 safety warning signs.

The signs

MUST

be installed on the front and back of the

gate where they will be visible in the area of the gate.

Permanently secure each warning sign to the gate.

Immediately replace a damaged or missing warning sign.

Содержание MM560













































Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды

Mighty Mule MM560, Руководство по установке

Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды