Mighty Mule MM560 страница 39 Скачать руководство пользователя

Страница: 39 / 44

MM560 Installation Instructions

POWER IN LED

CHARGING LED

Steady ON

Battery Charging

Blinking

Battery Fully Charged

OFF

Test charging circuit, check battery

OFF

No AC/Solar Power, check battery

OFF

Blinking

Check battery, incoming AC transformer or solar

OFF

Steady ON

Test charging circuit and check incoming AC trans-

former or solar and check battery

FUSE

BATT+

BATT-

1 2 3 4

STATUS

LEARN RMT

RECEIVER

LEARN

MAST LIMIT

LEARN

2ND LIMIT

ALM

OFF

SOFT START OFF
WARNING OFF
OPEN PULL
2ND OPEN DLY.
MODE1 OFF
MODE2 OFF

ON
ON
PUSH
SIMULT.
ON
ON

120 MIN

MAX

CHARGING

POWER IN

GTO RCVR.

WHT

BRN

RED

BLK

GRN

WHT

BRN

RED

BLK

GRN

BLK

RED

CLE

SAFET

EXIT

SHADO

OPEN EDGE

LOCK

PWR

AUX

RLY

POWER

INPUT

CONTROL OUTPUTS

MASTER OPERATOR

2ND OPERATOR

CONTROL INPUTS

AUTO CLOSE TIME

STALL FORCE

OSE

EDGE

GTO 18 VOLT

TRANSF. OR

SOLAR PANEL

DIAG

PORT

CHARGING

POWER IN

RED LED

GREEN LED

Battery/Power Troubleshooting

If your Gate Operator is not operating properly, please follow the steps below:

1. First use the procedures found in the Troubleshooting Guide (see page 25).

2. Use the 24/7 Troubleshooting Wizard at http://support.gtoinc.com.

3. If you are unable to solve the problem, call the GTO Service Department at (800) 543-1236, or (850) 575-

4144. Refer to the serial number (located on the right side of the control box) and date of purchase when

calling for assistance.

4. If repair or replacement of your gate operator is necessary, the Service Department will assign a Return

Goods Authorization (RGA) number to you.

5. Securely pack the component(s) authorized for return to the factory. Include a copy of your sales receipt

for the purchase of the product(s). Write the RGA number issued to you on the outside of the package in

LARGE BOLD PRINT.

Ship the package(s) freight prepaid to: GTO, 3121 Hartsfield Road, Tallahassee, Florida, USA 32303.

NOTE: Products returned to GTO without a Return Goods Authorization (RGA) number in LARGE

BOLD PRINT on the outside of the package WILL NOT be accepted. Also, items returned to GTO

freight collect WILL NOT be accepted.

Repair Service

GTO Technical Service and Installation Assistance

8:00am–7:00pm • Monday–Friday (EST)

Toll Free Support: 800-543-1236 • Fax: 850-575-8950

24/7 Troubleshooting Wizard: http://support.gtoinc.com

Содержание MM560













































Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды

Mighty Mule MM560, Руководство по установке

Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды