Mighty Mule MM560 Скачать руководство пользователя | Manualshive

Страница: 36 / 44

background image

33

MM560 Installation Instructions

Maintenance & Troubleshooting

Maintenance Tips

POWER

INPUTS

LOCK

PWR

AUX

RLY

CONTROL

OUTPUTS

GTO 18VOLT

TRANSFORMER

OR SOLAR

Wire from

Automatic

GTO Lock

GTO

LO

CK

Connecting GTO Automatic Lock

Connecting Additional Devices

GTO Lock Connection:

Connect the red and black leads from the lock to the “LOCK

PWR” inputs on the opener control board.

GTO Lock:

For use exclusively with GTO Lock (FM143 or FM144).

Connecting other devices to these terminals may cause incorrect

operation and void your warranty. You do not use the lock board

with this control board.

• These 2 terminals are normally open 'dry-contact' (no voltage) relay ouput.

• These 2 terminals are ON (shorted) whenever the gate is moving and OFF (opened) otherwise.

• These 2 terminals maximum rating is 24Vdc, 1 Amp.

Connecting Other Auxiliary Devices

(Mag Locks, Sirens, Lights. . .}

Monthly, test the obstruction and entrapment protection systems.
Monthly, service the gate operator (make sure the power switch is OFF). Clean extended operator arm with a soft, dry clean cloth. After
cleaning, apply a high quality silicon spray to a soft dry cloth and wipe the push/pull tube. DO NOT directly spray the tube!
On all gates weighing 250 lb. or more, routinely grease the ball bearing hinges at least 4 times a year; more frequently if the gates are
near a coastal area.
Monthly, turn off the power switch and disconnect the Mighty Mule and move the gate to make sure the gate is moving freely without
sticking or binding. Lubricate the hinges or repair the gate as required before reattaching the Mighty Mule.
Monthly, check the gate system for potentially entrapments from new landscaping or construction. Eliminate or guard as required.
Monthly, check that the warning signs are mounted on each side of the gate and clearly visible. Replace the signs if they are missing or
damaged.
Replace batteries every 2-3 years and properly recycle old batteries.

«
...
34
35
36
37
38
...
»

Содержание MM560













































Отзывы:

Нет отзывов

Похожие инструкции для MM560

Бренд: WALKY Страницы: 12

Бренд: GATEXPERT Страницы: 22

Бренд: RAMSET Страницы: 25

Бренд: SmartPower Страницы: 17

Бренд: CAME Страницы: 2

Бренд: DITEC Страницы: 42

entrematic TRAFFIC C

Бренд: DITEC Страницы: 44

Бренд: Calimet Страницы: 22

Бренд: CAME Страницы: 32

Бренд: CiA Страницы: 8

Бренд: GDS Страницы: 18

Бренд: ZEC Automation Страницы: 23

Бренд: Topens Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды