Mighty Mule MM560 Скачать руководство пользователя

Страница: 2 / 44

Product Usage

The Mighty Mule Gate Operator meets all of the safety requirements of a

Class I

Residential Vehicular Gate Operator and is

intended for use solely with vehicular swing gates in single-family residential applications that meet the Class I category listed

in the table below.

Residential Vehicular Gate Operator-Class I:

A vehicular gate operator (or system) intended for

use in garages or parking areas associated with a

residence of one-to-four single families.

Commercial/General Access Vehicular Gate

Operator-Class II:

A vehicular gate operator (or

system) intended for use in a commercial location

or building such as a multi-family housing unit (five

or more single family units), hotel, garages, retail

store, or other buildings accessible by or servicing

the general public.

Industrial/Limited Access Vehicular Gate

Operator–Class III:

A vehicular gate operator (or

system) intended for use in an industrial location or

building such as a factory or loading dock area or

other locations not accessible by or intended to service

the general public.

Restricted Access Vehicular Gate Operator–

Class IV:

A vehicular gate operator (or system)

intended for use in an industrial location or building

such as a factory or loading dock area or other

locations not accessible by or intended to service the

general public.

Vehicular Gate Operator Class Categories

WARNING

This equipment meets Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has

hazards associated with its use and therefore by installing this product the installer and user accept

full responsibility for following and noting the installation and safety instructions. Failure to follow

installation and safety instructions can result in hazards developing due to improper assembly. You agree

to properly install this product and that if you fail to do so GTO Access Systems, LLC, shall in no event

be liable for direct, indirect, incidental, special or consequential damages or loss of profits whether based

in contract tort or any other legal theory during the course of the warranty or at any time thereafter. The

installer and/or user agree to assume responsibility for all liability and use of this product releasing GTO

Access Systems, LLC, from any and all liability. If you are not in agreement with this disclaimer or do

not feel capable of properly following all installation and safety instructions you may return this product

for full replacement value.

READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY

before attempting to install and

use this automatic gate operator. This gate operator produces a high level of force. Stay clear of the unit

while it is operating and exercise caution at all times.

ALL AUTOMATIC GATE OPERATORS ARE INTENDED FOR USE ON VEHICULAR GATES ONLY.

Содержание MM560













































Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды

Mighty Mule MM560, Руководство по установке

Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды