Mighty Mule MM560 Скачать руководство пользователя

Страница: 19 / 44

MM560 Installation Instructions

Assemble post bracket parts.

NOTE: A Push-to-Open Bracket

FM148 is required for this type of installation (not included).

PTO

Bracket

FM148

11”

Mounting Push-to-Open Opener to Gate

Attach opener to gate bracket and secure with hardware required.

Swing gate to OPENED position. Check clearance/binding by inspecting

the alignment. The Maximum stroke is 20 inches. Secure post pivot bracket

to post bracket as shown in Step 7 on the next page, when clearance is OK
in both open and closed positions.

TIP: Turning the pivot bracket over

gives more hole alignment options for the post pivot bracket assembly.

With gate in CLOSED position, using clamps, secure opener to

gate post and center cross member of gate.

Gate Opener Installation

Recommended reinforcement and gate bracket mounting

examples.

Gate

Bracket

Thin Walled

Tube Gate

Gate

Bracket

1” x 6” Wood Reinforcement

Panel

Gate

Bracket

Wood or Metal

Reinforcement

(not supplied)

FRONT VIEW

SIDE VIEW

Mounting Plate Created for Decorative Gate

(required but not supplied)

Reinforcement and Gate Bracket Mounting

Muffler Clamp

(not supplied)

Remove clevis pin from the gate bracket and support loose

opener.

2" minimum

pinch-point clearance

Maximum Stroke 20”

Top View

Closed

Position

Open

Position

Your Property

Содержание MM560













































Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды

Mighty Mule MM560, Руководство по установке

Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды