Mighty Mule MM560 Скачать руководство пользователя

Страница: 37 / 44

MM560 Installation Instructions

Troubleshooting Guide

If your gate opener does not function properly after it is installed, use this guide before calling the GTO Service Department.

Audible Feedback

Indication

Possible Diagnosis

Check

1 short beep upon activation Blown Fuse

Low or Bad Battery

Loose Battery Connection

• Fuse

• Battery Under Load

• Battery Harness Connections

A series of beeps that stop

and do not repeat after

power-up

Circuit Board Powered Up &

Ready

• Normal Operation

Continuous Uninterrupted

Alarm

Circuit Board Senses an

Obstruction

• Path of Gate

• Gate for Level and Plumb

• Stall Force Adjustment

• For diagnostic purposes, temporarily disconnect the

external obstruction detection devices

• Rev Counter

1 beep with 10 seconds off Low Battery Condition

• Fuses

• Battery Harness Connections

• Battery Under Load

1 beep then 2 beeps, then

pause and repeats

Master Motor Terminals

Shorted

• Connections to Master Inputs

• Master Arm Power Cable

• Motor

• Circuit Board

1 beep then 3 beeps, then

pause and repeats

Second Motor Terminals

Shorted

• Connections to Second Inputs

• Second Arm Power Cable

• Motor

• Circuit Board

1 beep with 2 seconds, then

pause and repeats

Master Arm Limit Switch

Error

• Connections to Master Inputs

• Master Arm Power Cable

3 beeps with 2 seconds, then

pause and repeats

Master Arm Rev Counter

Error

• Connections to Master Inputs

• Master Arm Power Cable

• Rev Counter

VOLTAGE READINGS

18 Vac Transformer ............................................................................................18.0 to 22.0 Vac, 2200 mA

5 W Solar panel (single) ....................................................................................18.0 to 22.0 Vdc, 300 mA

* measure voltage at panel and control box, in full sun; this will increase by approximately 300mA for

each additional solar panel.

Two 12 V, 7 amp hour Batteries .....................................................................12.5 to 13.5 Vdc 7.0 Ah

*measure voltage at battery terminals with battery disconnected from circuit board

Charging circuit .................................................................................................13.3 to 14.8 Vdc

*measure voltage at battery terminals with battery connected to circuit board and GREEN "POWER IN"

LED is ON.

Содержание MM560













































Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды

Mighty Mule MM560, Руководство по установке

Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды