Mighty Mule MM560 страница 41 Скачать руководство пользователя

Страница: 41 / 44

MM560 Installation Instructions

Accessories are Available From Your Retail Store

ACCESSORIES

AUT

OMA

TIC

GAT

E LO

ELECTRONIC SECURITY L

OCK

Solar Panel (FM121)

The

Solar Panel

is a 5 watt solar powered battery charger for use with the

FM500 & MM560

gate

operator systems. Particularly suited for remote installations, each

Solar Panel

comes with tubular

steel support, mounting clips, wire connectors, and 8 ft. of low voltage wire (see Low Voltage Wire

for additional wire). The

Mighty Mule®

control board has clearly labeled terminal connections for

easy installation of the

Solar Panel

. Installation in some regions of the world will require multiple

solar panels for adequate charging power. Dual gates require a minimum of 10 watts of solar charging

power. (10 watt solar panels are available)

Push Button Control (FM132)

Unlit doorbell button for remote entry or exit control. Wires directly to the control board and uses 16

gauge multi-stranded, dual conductor low voltage wire (sold separately).

Pin Lock (FM133)

The

Pin Lock

substitutes for the clevis pin at the front end of the Mighty Mule® gate openers. Helps

prevent theft of the operator from the gate, while allowing quick release of the operator.

Key Chain Two Button Transmitter (FM134)

The Key Chain Mini Transmitter is a two button version of the

Mighty Mule®

entry transmitter and

has the same adjustable code settings. (battery is included)

Single Button Transmitter (FM135)

The

Mighty Mule®

entry transmitter, with adjustable code settings, is standard equipment with all

Mighty Mule®

systems. (battery is included)

Digital Keypad (FM137)

The specially designed digital keypad can be easily installed as a wireless or wired keypad. It can be

programmed to use up to 25 different personal identification number (PIN) codes. Each code is face

programmable with additional security features built in. Wired installations require 16 gauge, low

voltage, multi-stranded, dual conductor, direct burial wire (sold separately). Requires 3 AA batteries

(not included).

Mounting Post (FM100) - In Ground

This black powder coated pedestal is designed to provide convenient access to your keypad, wireless

intercom, or other access control device from your vehicle. With its break down design it is easy to

install and works well in most standard applications. Surface Mount Flanges (F102) and Extensions

(F103) for added height are available.

Mighty Mule® Vehicle Sensor (FM138)

The Gate Opening Sensor is designed for residential and agricultural applications and is compatible

with most Mighty Mule® automatic gate opener models (see Sensor Box for model compatibility).

The Sensor is an electromagnetic sensor, which offers 'hands free' operation of the Mighty Mule®

Gate Operator with a 12 ft. radius of detection of vehicles in motion.

Automatic Gate Lock (FM143)

MUST for added security. Solenoid driven, with a steel housing. Unlocks and locks automatically

as gates open and close. Used with

Mighty Mule®

DC swing gate operating systems for maximum

stability and security. Comes with a keyed manual release. Recommended for gates over 8 ft. long.

Ideal for high wind areas.

ABC

DEF

GHI

JKL

MNO

PRS

TUV

WXY

Содержание MM560













































Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды

Mighty Mule MM560, Руководство по установке

Результаты поиска

Содержание MM560

Отзывы:

Похожие инструкции для MM560

Бренды по названию

Популярные бренды