Merida All Terrain Bikes Скачать руководство пользователя страница 46

Страница: 46 / 139

9.9. Checking and adjusting hydraulic

disc brakes

Regularly check the lines and connections for

leaks while pulling on the lever. If brake fluid

leaks out, contact your MERIDA dealer imme-

diately, as a leak can render your brakes use-

less.

To adjust the travel of the lever, turn the

adjusting bolt located on the setting bush of

the lever by using a small screwdriver or an

Allen wrench. Keep in mind that the adjust-

ing range of the bolt is limited. Do not try to

unscrew the bolt beyond this range.

Check the pads for wear (if necessary by

inspecting the nose or ear-shaped metal lugs

protruding from behind the brake calliper).

When these wear indicators have approached

the disc with about a millimetre to spare, you

should dismount the pads according to the

manufacturer’s instructions and examine them

carefully.

Loose connections and leaky brake

lines drastically impair the braking

power. If you find leaks in the brake sys-

tem or buckled lines, contact your dealer.

Do under no circumstances use your bike

anymore.

Leaking brake fluid may harm your

health and is also aggressive against

paint etc.

Please clean the pads and disc exclu-

sively with spirit or brake cleaner.

9. The brake system

Содержание All Terrain Bikes












































































































































Результаты поиска

Содержание All Terrain Bikes

Отзывы:

Похожие инструкции для All Terrain Bikes

Бренды по названию

Популярные бренды

Merida All Terrain Bikes, Руководство пользователя

Результаты поиска

Содержание All Terrain Bikes

Отзывы:

Похожие инструкции для All Terrain Bikes

Бренды по названию

Популярные бренды