Merida All Terrain Bikes Скачать руководство пользователя страница 41

Страница: 41 / 139

9.6. Adjustment possibilities at the lever

To adjust the brakes at the lever, release the

knurled lock ring located at the point where

the brake cable enters the brake lever on

the handlebars. Release the knurled, slotted

adjusting bolt by a few turns. In this way

you shorten the free travel of the brake lever.

Keeping the adjusting bolt fixed, tighten the

lock ring against the brake lever mount. This

prevents the adjusting bolt from coming loose

by itself.

Ensure that the slot of the bolt faces neither

forward nor upward, as this would permit

water or dirt to enter.

9.6. Adjustment possibilities at the brake

pads and bowden cables

Another possibility to adjust the brake is by

means of an adjusting bolt located at the front

brake. Release in this area the knurled nut

of the bolt through which the cable passes,

unscrew the adjusting bolt by a few turns and

finish by retightening the knurled nut relative

to the brake arm.

9. The brake system

The adjustment of the rear brake can be

performed in the same way. In addition, the

rear brake cable which is running along the

bottom of the frame tube can be adjusted by

means of another adjusting bolt. Release the

lock nut at the cable holder and unscrew the

adjusting bolt by a few turns. Then retighten

the lock nut in order to avoid a coming loose

of the adjusting bolt by itself.

Test the brake in standing after adjust-

ing it. Make sure the brake pads

engage fully with the rim when you pull

them hard.

Содержание All Terrain Bikes












































































































































Результаты поиска

Содержание All Terrain Bikes

Отзывы:

Похожие инструкции для All Terrain Bikes

Бренды по названию

Популярные бренды

Merida All Terrain Bikes, Руководство пользователя

Результаты поиска

Содержание All Terrain Bikes

Отзывы:

Похожие инструкции для All Terrain Bikes

Бренды по названию

Популярные бренды