Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 99

Страница: 99 / 107

Tube Ref

No.

Description

Where Used

Part No.

2-4-C with PTFE

Propeller shaft

92-802859A 1

IMPORTANT: To prevent the propeller hub from corroding and seizing to the

propeller shaft (especially in saltwater), always apply a coat of the

recommended lubricant to the entire propeller shaft at the recommended

maintenance intervals, and also each time the propeller is removed.

2. Flo‑Torq I drive hub propellers ‑ Install forward thrust hub, propeller,

propeller nut retainer, and propeller nut onto the shaft.

a -

Propeller nut

b -

Propeller nut retainer

c -

Propeller

d -

Forward thrust hub

3. Flo‑Torq II drive hub propellers ‑ Install forward thrust hub, propeller,

replaceable drive sleeve, rear thrust hub, propeller nut retainer, and

propeller nut onto the shaft.

a -

Propeller nut

b -

Propeller nut retainer

c -

Rear thrust hub

d -

Replaceable drive sleeve

e -

Propeller

f -

Forward thrust hub

4. Place the propeller nut retainer over the pins. Place a block of wood

between the gearcase and propeller. Tighten the propeller nut to the

specified torque.

Description

lb‑in.

lb‑ft

Propeller nut

26903

26904

INSTALLATION

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 99 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: