Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 57

Страница: 57 / 107

Trim Tab Adjustment

Propeller steering torque will cause your boat to pull in one direction. This

steering torque is a normal result from your outboard not trimmed with the

propeller shaft parallel to the water surface. The trim tab can help to

compensate for this steering torque in many cases and can be adjusted within

limits to reduce any unequal steering effort.

26816

NOTE: Trim tab adjustment will have little effect reducing steering torque if the

outboard is installed with the antiventilation plate approximately 50 mm (2 in.)

or more above the boat bottom.
TRIM TAB ADJUSTMENT

Operate your boat at normal cruising speed trimmed to desired position by

installing the tilt pin in the desired tilt pin hole. Turn your boat left and right and

note the direction the boat turns more easily.
If adjustment is necessary, loosen the trim tab bolt and make small adjustments

at a time. If the boat turns more easily to the left, move the trailing edge of the

trim tab to the left. If the boat turns more easily to the right, move the trailing

edge of the trim tab to the right. Tighten the bolt and test.

FEATURES AND CONTROLS

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 57 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: