Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 70

Страница: 70 / 107

Top Cowl Removal and Installation

REMOVAL

Pull out the rear lock lever and remove the top cowl.

28439

INSTALLATION

1. Lower the top cowl over the engine.
2. Bring the front of the cowl down first and engage the front hook. Lower the

cowl into its seated position and apply downward pressure to the back of

the cowl to lock it in place. Gently pull up on the back of cowl to make

sure it is securely fastened.

28445

Exterior Care

Your outboard is protected with a durable baked enamel finish. Clean and wax

often using marine cleaners and waxes.

Battery Inspection

The battery should be inspected at periodic intervals to ensure proper engine

starting capability.
IMPORTANT: Read the safety and maintenance instructions which accompany

your battery.

1. Turn off the engine before servicing the battery.

MAINTENANCE

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 70 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: