Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 81

Страница: 81 / 107

2. Remove the filter by turning the filter counterclockwise.

58164

3. Clean the mounting base. Lubricate the new oil filter gasket with engine

oil. Do not use grease. Thread the filter on until the gasket contacts the

base, then tighten 3/4 to 1 turn.

OIL FILLING

1. Remove the oil fill cap and add oil to the proper operating level.
2. Idle the engine for five minutes and check for leaks. Stop the engine and

check the oil level on the dipstick. Add oil if necessary.

a -

Oil fill cap

Gearcase Lubrication

When adding or changing gearcase lubricant, visually check for the presence of

water in the lubricant. If water is present, it may have settled to the bottom and

will drain out prior to the lubricant, or it may be mixed with the lubricant, giving it

a milky colored appearance. If water is noticed, have the gearcase checked by

your dealer. Water in the lubricant may result in premature bearing failure or, in

freezing temperatures, will turn to ice and damage the gearcase.
Examine the drained gearcase lubricant for metal particles. A small amount of

fine metal particles indicates normal gear wear. An excessive amount of metal

filings or larger particles (chips) may indicate abnormal gear wear and should

be checked by an authorized dealer.

28418

MAINTENANCE

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 81 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: