manualshive.com logo in svg

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 86 / 107

Поделиться
Скачать
Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 86

Engine Will Not Start

POSSIBLE CAUSES

•

Lanyard stop switch not in RUN position.

•

Incorrect starting procedure. Refer to 

Operation

 section.

•

Old or contaminated gasoline.

•

Engine flooded. Refer to 

Operation

 section.

•

Fuel is not reaching the engine.

a. Fuel tank is empty.
b. Fuel tank vent not open or restricted.
c. Fuel line is disconnected or kinked.
d. Primer bulb not squeezed.
e. Primer bulb check valve is faulty.
f. Fuel filter is obstructed. Refer to 

Maintenance

 section.

g. Fuel pump failure.
h. Fuel tank filter obstructed.

•

Ignition system component failure.

•

Wiring or electrical connection faulty.

•

Spark plugs fouled or defective. Refer to 

Maintenance

 section.

Engine Runs Erratically

POSSIBLE CAUSES

•

Guardian System activated. Refer to 

Features and Controls—Warning

System 

‑

 Manually Starting Models

.

•

Spark plugs fouled or defective. Refer to 

Maintenance

 section.

•

Incorrect setup and adjustments.

•

Fuel is being restricted to the engine.

a. Engine fuel filter is obstructed. Refer to 

Maintenance

 section.

b. Fuel tank filter obstructed.
c. Stuck anti‑siphon valve located on permanently built‑in type fuel tanks.
d. Fuel line is kinked or pinched.

•

Fuel pump failure.

•

Ignition system component failure.

Performance Loss

POSSIBLE CAUSES

•

Engine Guardian System activated. Refer to 

Features and Controls—

Warning System 

‑

 Manually Starting Models

.

•

Throttle not fully open.

TROUBLESHOOTING

  

78

eng

Содержание 40 FourStroke Tiller Handle












































































































Отзывы:

Нет отзывов