Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 69

Страница: 69 / 107

WARNING

Rotating propellers can cause serious injury or death. Never operate the boat

out of the water with a propeller installed. Before installing or removing a

propeller, place the drive unit in neutral and engage the lanyard stop switch

to prevent the engine from starting. Place a block of wood between the

propeller blade and the anti‑ventilation plate.

1. Place the outboard in either the operating position (vertical) or in a tilted

position.

2. Remove the propeller. Refer to

Propeller Replacement

3. Thread a water hose into the rear fitting. Partially open the water tap (1/2

maximum). Do not open the water tap all the way as this allows a high

pressure flow of water.

IMPORTANT: Do not run engine above idle when flushing.

4. Shift the outboard into neutral. Start the engine and flush the cooling

system for at least five minutes. Keep the engine speed at idle.

5. Stop the engine. Turn off the water and remove the hose. Reinstall the

propeller.

28518

MAINTENANCE

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 69 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: