Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 93

Страница: 93 / 107

Do not overpower or overload your boat. Most boats will carry a required

capacity plate indicating the maximum acceptable power and load as

determined by the manufacturer following certain federal guidelines. If in doubt,

contact your dealer or the boat manufacturer.

U.S. COAST GUARD CAP ACITY
MAXIMUM HORSEPOWER XXX

MAXIMUM PERSON
CAPACITY (POUNDS)

XXX

MAXIMUM WEIGHT
CAPACITY

XXX

26777

START IN GEAR PROTECTION

WARNING

Starting the engine with the drive in gear can cause serious injury or death.

Never operate a boat that does not have a neutral‑safety‑protection device.

The remote control connected to the outboard must be equipped with a start in

neutral only protection device. This prevents the engine from starting in gear.

SELECTING ACCESSORIES FOR YOUR OUTBOARD

Genuine Mercury Precision or Quicksilver Accessories have been specifically

designed and tested for your outboard. These accessories are available from

Mercury Marine dealers.
IMPORTANT: Check with your dealer before installing accessories. The misuse

of approved accessories or the use of nonapproved accessories can damage

the product.
Some accessories not manufactured or sold by Mercury Marine are not

designed to be safely used with your outboard or outboard operating system.

Acquire and read the installation, operation and maintenance manuals for all

your selected accessories.

ELECTRIC FUEL PUMP

If an electric fuel pump is used, the fuel pressure must not exceed 27.58 kPa

(4 psi) at the engine. If necessary, install a pressure regulator to regulate the

pressure.

INSTALLATION

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 93 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: