Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 56

Страница: 56 / 107

Throttle Grip Friction Adjustment ‑ Tiller Handle Models

Throttle grip friction knob ‑ Turn friction knob to set and maintain the throttle at

desired speed. Turn knob clockwise to tighten friction and turn knob

counterclockwise to loosen friction.

a -

Loosen friction

b -

Tighten friction

Steering Friction Adjustment ‑ Tiller Handle Models

NOTE: Steering friction adjustment is only provided on models with tiller

handles.

Adjust this lever to achieve the desired steering friction (drag) on the tiller

handle. Move lever to the left to tighten friction or move to the right to loosen

friction.

NOTE: To maintain proper adjustment, the locknut located on top of the

steering friction lever pivot shaft can be tightened.

a -

Tighten friction

b -

Loosen friction

c -

Locknut

WARNING

Insufficient friction adjustment can cause serious injury or death due to loss

of boat control. When setting the friction adjustment, maintain sufficient

steering friction to prevent the outboard from steering into a full turn if the

tiller handle is released.

19807

26811

FEATURES AND CONTROLS

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 56 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: