Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 75

Страница: 75 / 107

7. Flo‑Torq I drive hub propellers ‑ Install the forward thrust hub, propeller,

propeller nut retainer, and propeller nut onto the shaft.

a -

Propeller nut

b -

Propeller nut retainer

c -

Propeller

d -

Forward thrust hub

8. Place the propeller nut retainer over the pins. Place a block of wood

between the gearcase and propeller. Tighten propeller nut to the specified

torque.

Description

lb‑in.

lb‑ft

Propeller nut

–

9. Align the flat sides of the propeller nut with the tabs on the propeller nut

retainer. Secure the propeller nut by bending the tabs up and against the

flats on the propeller nut.

a -

Pins

b -

Tabs

10. Reflex hub ‑ Install the thrust washer onto the propeller shaft.

43671

11. Install the propeller.
12. Install the aft washer, the tab washer, and secure with the propeller nut

included with the kit. Tighten the nut to the specified torque. Bend the tabs

on the tab washer onto the nut.

26903

26906

MAINTENANCE

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 75 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: