Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 52

Страница: 52 / 107

NOTE: Should overheating occur and you are stranded, stop the engine and

allow it to cool down. This will usually allow some additional low speed (idle)

running time before the engine starts to overheat again.
LOW OIL PRESSURE

The warning system will be activated if the oil pressure drops too low. First,

stop the engine and check the oil level. Add oil if necessary. If the oil is at the

recommended level and the warning horn continues to sound, consult your

dealer. Engine speed will be limited to 2000 RPM, however you should not

continue to run engine.

SmartCraft Product

A Mercury SmartCraft System instrument package can be purchased for this

outboard. A few of the functions the instrument package will display are engine

RPM, coolant temperature, oil pressure, water pressure, battery voltage, fuel

consumption, and engine operating hours.
The SmartCraft instrument package will also aid in Engine Guardian

diagnostics. The SmartCraft Instrument package will display critical engine

alarm data and potential problems.

Manual Tilt System

Models without power trim are equipped with a tilt assist system that allows the

operator to easily tilt and lock the outboard at any tilt position from full down to

full up.
This tilt system is designed to be adjusted when the outboard is idling in neutral

or with the engine turned off.
Before operating, the outboard must be locked in its tilt position by moving the

tilt lock lever to the

lock/run

position.

WARNING

Operating the engine without engaging the tilt lock lever can cause serious

injury or death. The outboard can tilt upwards when decelerating or operating

in reverse, causing loss of boat control. Always lock the outboard in its run

position before operating.

BASIC TILTING OPERATION

Move tilt lock lever to the tilt position. Tilt outboard to desired position and lock

in place by moving the tilt lock lever back to the lock/run position.

a -

Tilt position

b -

Lock/run position

26802

FEATURES AND CONTROLS

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 52 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: