Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 76

Страница: 76 / 107

IMPORTANT: The Flo‑Torq Reflex drive hub requires the use of the propeller

nut included with the drive hub kit. The use of a propeller nut that was not

included with the Flo‑Torq Reflex drive hub kit will result with the nylon portion

of the locknut not fully engaging the propeller shaft threads.

a -

Thrust washer

b -

Propeller

c -

Aft washer

d -

Tab washer

e -

Nut

13. Rotate the propeller to verify interference or binding does not exist

between the gear housing and the propeller.

Description

lb‑in.

lb‑ft

Nut

–

NOTE: A small amount of rotation play is normal.

14. Install the spark plug leads.

Spark Plug Inspection and Replacement

WARNING

Damaged spark plug boots may emit sparks that can ignite fuel vapors under

the engine cowl, resulting in serious injury or death from a fire or explosion.

To avoid damaging the spark plug boots, do not use any sharp object or

metal tool to remove the spark plug boots.

1. Remove the spark plug boots. Twist the rubber boots slightly and pull off.

26899

43652

MAINTENANCE

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 76 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: