Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 51

Страница: 51 / 107

Warning System ‑ Manual Starting Models

The outboard warning system incorporates a warning horn below the tiller

handle.

a -

Warning horn below tiller handle

WARNING SYSTEM OPERATION

The warning horn will emit either a continuous beep or intermittent short beeps,

and engine speed will be limited to 2000 RPM. This will alert the operator and

help identify the following situations.

Warning System

Function

Sound

Description

Engine Over Temperature

Continuous

Engine Overheat

Low Oil Pressure

Intermittent Short Beeps Low Oil Pressure

ENGINE OVERHEAT

If the engine overheats, immediately reduce throttle speed to idle. Shift the

outboard into neutral and check for a steady stream of water coming out of the

water pump indicator hole.

28521

If no water is coming out of the water pump indicator hole or flow is intermittent,

stop engine and check cooling water intake holes for obstruction. If no

obstruction is found, this may indicate a blockage in the cooling system or a

water pump problem. Have the outboard checked by your dealer. Operating the

engine while overheated will cause engine damage.
If a steady flow of water is coming out of the water pump indicator hole and the

engine continues to overheat, consult your dealer. Operating an overheated

engine will cause engine damage.

28831

FEATURES AND CONTROLS

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 51 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: