Mercury 40 FourStroke Tiller Handle Скачать руководство пользователя страница 65

Страница: 65 / 107

2. Shift the outboard to the neutral (N) position.

58150

WARNING

The neutral‑speed‑protection device is inoperative when starting the engine

with the emergency starter rope. Set the engine speed at idle and the gear

shift in neutral to prevent the outboard from starting in gear.

WARNING

The exposed moving flywheel can cause serious injury. Keep your hands,

hair, clothing, tools, and other objects away from engine when starting or

running the engine. Do not attempt to reinstall the flywheel cover or top

cowl when engine is running.

3. Place the starter rope knot into the flywheel notch and wind the rope

clockwise around the flywheel.

4. Pull the starter rope to start the engine.

26848

OPERATION

eng

Содержание 40 FourStroke Tiller Handle












































































































Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы:

Mercury 40 FourStroke Tiller Handle, Инструкция по эксплуатации, техническому обслуживанию, гарантии и установке, Страница: 65 / 107

Результаты поиска

Содержание 40 FourStroke Tiller Handle

Отзывы: