Mercury 135 Verado FourStroke Скачать руководство пользователя страница 92

Страница: 92 / 123

Steering Link Rod Fasteners

IMPORTANT: The steering link rod that connects the steering cable to the

engine must be fastened using special washer head bolt ("a" ‑ Part Number

10‑849838) and self‑locking nylon insert locknuts ("c" & "d" ‑ Part Number

11‑826709113). These locknuts must never be replaced with common nuts

(non‑locking) as they will work loose and vibrate off freeing the link rod to

disengage.

WARNING

Improper fasteners or improper installation procedures can result in

loosening or disengagement of the steering link rod. This can cause a

sudden, unexpected loss of boat control, resulting in serious injury or death

due to occupants being thrown within or out of the boat. Always use required

components and follow instructions and torque procedures.

a -

Special washer head bolt (10‑849838)

b -

Flat washer (2)

c -

Nylon insert locknut (11‑826709113)

d -

Nylon insert locknut (11‑826709113)

Description

lb‑in.

lb‑ft

Special washer head bolt

–

Nylon insert locknut "d"

–

Nylon insert locknut "c"

Tighten until seats, then back off 1/4

turn

Assemble the steering link rod to steering cable with two flat washers and

self‑locking nylon insert locknut. Tighten the locknut until it seats, then back nut

off 1/4 turn.

29746

MAINTENANCE

eng

Содержание 135 Verado FourStroke




























































































































Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды

Mercury 135 Verado FourStroke, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды