Mercury 135 Verado FourStroke Скачать руководство пользователя страница 81

Страница: 81 / 123

6. Secure the flywheel cover to the rear mounting posts with two bolts with

washers. Tighten bolts to the specified torque.

a -

Flywheel cover bolt and washer (2)

b -

FSM vent hose

c -

Crankcase ventilation hose

Description

lb‑in.

lb‑ft

Flywheel cover bolt

88.5

–

Fuel System

WARNING

Fuel is flammable and explosive. Ensure that the key switch is off and the

lanyard is positioned so that the engine cannot start. Do not smoke or allow

sources of spark or open flame in the area while servicing. Keep the work

area well ventilated and avoid prolonged exposure to vapors. Always check

for leaks before attempting to start the engine, and wipe up any spilled fuel

immediately.

IMPORTANT: Use an approved container to collect and store fuel. Wipe up

spilled fuel immediately. Material used to contain spilled fuel must be disposed

of in an approved receptacle.
Before servicing any part of the fuel system:

1. Stop engine and disconnect the battery.
2. Perform fuel system service in a well‑ventilated area.
3. Inspect any completed service work for sign of fuel leakage.

15247

MAINTENANCE

eng

Содержание 135 Verado FourStroke




























































































































Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды

Mercury 135 Verado FourStroke, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды