Mercury 135 Verado FourStroke Скачать руководство пользователя страница 54

Страница: 54 / 123

Turning off one of the outer engines while underway will cause the center

engine to go into forced neutral/idle. Operation to the center engine can be

restored by moving the control handle of the functioning outer engine back into

neutral position and then engaging. The center engine speed and gear shift will

then be controlled by the functioning outer engine.
Turning off the center engine while underway will have no effect on the

operation of the outer engines.
If a failure should occur while underway which causes one of the outer engines

into forced neutral/idle condition, the center engine will also be forced to

neutral/idle. Operation to the center engine can be restored by moving the

control handle of the functioning outer engine back into neutral and then

engaging.

QUAD ENGINE THROTTLE AND SHIFT OPERATION

Movement of the handles on the remote control allows the boat operator to

control the engine throttle speed and gear shift positions of all four engines.
The throttle and shift function is dependent on what engines are running. The

following table represents the most common quad engine vessel personality for

shadow operation.
IMPORTANT: Quad engine vessel personalities may vary on which engines

are configured to be the master engines. It is possible to have the center

engines as the master and the outer engines configured as the shadow

engines. Therefore, the following table does not represent this type of vessel

personality.

Port Outer

Engine

Port

Inner

Engine

Starboard

Inner

Engine

Starboard

Outer Engine Control Handle Function

Running

Running Running

Running

Port inner and outer

engines throttle and shift

= controlled by port

control handle
Starboard inner and

outer engines throttle

and shift = controlled by

starboard control handle

Running

Running Off

Off

Port inner and outer

engines throttle and shift

= controlled by port

control handle

Off

Running

Starboard inner and

outer engines throttle

and shift = controlled by

starboard control handle

FEATURES AND CONTROLS

eng

Содержание 135 Verado FourStroke




























































































































Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды

Mercury 135 Verado FourStroke, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды