Mercury 135 Verado FourStroke Скачать руководство пользователя страница 82

Страница: 82 / 123

FUEL LINE INSPECTION

Visually inspect the fuel line for cracks, swelling, leaks, hardness, or other signs

of deterioration or damage. If any of these conditions are found, the fuel line

must be replaced.

WATER SEPARATING FUEL FILTER
NOTE: The warning system will turn on when water in the fuel filter reaches the

full level.

This filter removes moisture and debris from the fuel. If the filter holder

becomes filled with water, the water can be removed. If the filter becomes

plugged with debris, replace the filter.
Refer to the

Inspection and Maintenance Schedule

for the proper

maintenance interval.

Filter Removal

1. Turn ignition key switch to "OFF" position.
2. Remove fuel vapor purge relief valve cap located at the rear of the

engine.

14765

CAUTION

Failure to release pressure from the fuel system will result in fuel spraying

out, which can cause a fire or explosion. Allow the engine to cool

completely and release all fuel pressure before servicing any part of the

fuel system. Always protect eyes and skin from pressurized fuel and

vapors.

MAINTENANCE

eng

Содержание 135 Verado FourStroke




























































































































Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды

Mercury 135 Verado FourStroke, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды