Mercury 135 Verado FourStroke Скачать руководство пользователя страница 48

Страница: 48 / 123

Item Control

Function

1 LEVER

Enables the throttle and shift functions of both engines

to be controlled by the port lever.

SYNC

Turns off or on the auto‑synchronization feature. Refer

Sync

NOTE: Not all functions may be active.

Dock

Dock mode reduces throttle capacity to approximately 50% of normal throttle

demand, allowing finer control of engine power in close quarter situations.

51854

DOCK button

Throttle Only

NOTE: Throttle only mode should be used if the captain is not in command at

the helm. Placing the ERC in throttle only mode will avoid unintended gear

engagement. The engines will turn using the steering wheel and the RPM of

the engines can be increased while in the throttle only mode, but the gear

position will remain in neutral.

51855

THROTTLE ONLY button

To engage throttle only mode:

1. Place both ERC levers in neutral.

FEATURES AND CONTROLS

eng

Содержание 135 Verado FourStroke




























































































































Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды

Mercury 135 Verado FourStroke, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды