Mercury 135 Verado FourStroke Скачать руководство пользователя страница 99

Страница: 99 / 123

Crankcase Oil Pump

91‑90265A 5

11591

Aids in the removal of engine oil without

draining the crankcase.

4. Pump out the engine oil into an appropriate container.

DRAIN METHOD

1. Tilt outboard up to the trailer position.
2. Turn the outboard so the drain hole is facing downward.
3. Remove the drain plug/seal and drain the engine oil into an appropriate

container.

4. Lubricate seal washer on the drain plug with oil and reinstall.

15613

CHANGING OIL FILTER

IMPORTANT: To reduce or prevent oil spillage when removing the oil filter,

ensure the outboard is upright (not tilted) and the engine is cold or has not run

for at least one hour.

1. Remove the top cowl.
2. Place a rag or towel below the oil filter to absorb any spilled oil.

MAINTENANCE

eng

Содержание 135 Verado FourStroke




























































































































Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды

Mercury 135 Verado FourStroke, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды