Mercury 135 Verado FourStroke Скачать руководство пользователя страница 94

Страница: 94 / 123

• Trim Rod Ball Ends ‑ Turn the ball ends to work the lubricant into the

ball sockets.

28458

2. Lubricate the following with Extreme Grease or 2‑4‑C with PTFE.

Tube Ref

No.

Description

Where Used

Part No.

Extreme Grease

Propeller shaft

8M0071842

2-4-C with PTFE

Propeller shaft

92-802859A 1

• Propeller Shaft ‑ Refer to

Propeller Replacement

for removal and

installation of the propeller. Coat the entire propeller shaft with

lubricant to prevent the propeller hub from corroding and seizing to the

shaft.

26902

3. Lubricate the following with 2‑4‑C with PTFE or Extreme Grease.

Tube Ref

No.

Description

Where Used

Part No.

Extreme Grease

Swivel bracket, tilt support lever, tilt tube

8M0071842

2-4-C with PTFE

Swivel bracket, tilt support lever, tilt tube

92-802859A 1

• Swivel Bracket ‑ Lubricate through fitting.

MAINTENANCE

eng

Содержание 135 Verado FourStroke




























































































































Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды

Mercury 135 Verado FourStroke, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды