Mercury 135 Verado FourStroke Скачать руководство пользователя страница 121

Страница: 121 / 123

A decal on the transom bracket reminds the owner to check the fasteners

securing the outboard to the transom before each use.

51985

Decal on the transom bracket

Installing Outboard

WARNING

Failure to correctly fasten the outboard could result in the outboard propelling

off the boat transom resulting in property damage, serious injury, or death.

Before operation, the outboard must be correctly installed with the required

mounting hardware.

Have your dealer install your outboard and related accessories to ensure

proper installation and good performance.
The outboard must be secured to the transom with the four 12.7 mm (1/2 in.)

diameter mounting bolts and locknuts provided. Install two bolts through the

upper set of holes and two bolts through the lower set of holes.

27746

INSTALLATION INFORMATION

eng

111

Содержание 135 Verado FourStroke




























































































































Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды

Mercury 135 Verado FourStroke, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды