Mercury 135 Verado FourStroke Скачать руководство пользователя страница 40

Страница: 40 / 123

2. Trim Switch (if equipped) ‑ When the power trim switch is activated on the

ERC handle, the DTS command module senses a closed circuit for either

up or down trim. The DTS command module formulates a signal and

sends it to the PCM. The PCM closes the ground circuit to the up or down

trim relay.

a -

Forward

b -

Neutral

c -

Reverse

d -

Trim switch

3. Detent tension adjustment screw ‑ This screw can be adjusted to increase

or decrease the effort to move control handle out of detent positions.

Turning screw clockwise will increase tension. Adjust to tension desired.

4. Control handle tension adjustment screw ‑ This screw can be adjusted to

increase or decrease the tension on the control handle. This will help

prevent unwanted motion of the remote control handle in rough water.

Turn screw clockwise to increase tension and counterclockwise to

decrease tension. Adjust to tension desired.

a -

Caps (2)

b -

Detent tension

adjustment

c -

Control handle

tension adjustment

NOTE: The control handle tension and detent tension screws may require

periodic maintenance adjustment.

52360

52313

FEATURES AND CONTROLS

eng

Содержание 135 Verado FourStroke




























































































































Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды

Mercury 135 Verado FourStroke, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды