Mercury 135 Verado FourStroke Скачать руководство пользователя страница 77

Страница: 77 / 123

WARNING

Failure to properly secure the battery leads can result in a loss of power to

the Digital Throttle and Shift (DTS) system, leading to serious injury or death

due to loss of boat control. Secure the battery leads to the battery posts with

hex nuts to avoid loose connections.

Description

lb‑in.

lb‑ft

Hex nuts

13.5

120

–

IMPORTANT: Battery cable size and length is critical. Refer to Battery Cable

Size tables or engine installation manual for size requirements.
A decal advising against using deep cycle batteries and wing nuts should be

placed on or near the battery box for future service reference. One 5/16 in. and

one 3/8 in. hex nut is supplied per battery for wing nut replacement. Metric hex

nuts are not supplied.

54395

Place decal on or near battery box for future

service reference. Included with the engine

rigging components are 5/16" and 3/8” hex

nuts to be used for battery terminal wing nut

replacement. Metric hex nuts must be obtained

locally.

8M0085862

Refer to the outboard owner’s manual for

battery requirements.

Battery cable size and length is critical.

Refer to engine installation manual for

size requirements.

NOTICE

IMPORTANT:

DO NOT USE DEEP CYCLE BATTERIES!

13.5Nm (120 lb-in.)

DO NOT

USE

WINGNUTS

Air Filter

The air filter is located within the flywheel cover assembly. The air filter

removes airborne particles which may damage engine components. The air

filter design allows for maximum unrestricted air flow during engine operation.

AIR FILTER REMOVAL

1. Remove the FSM vent hose and the engine ventilation hose from the

flywheel cover.

MAINTENANCE

eng

Содержание 135 Verado FourStroke




























































































































Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды

Mercury 135 Verado FourStroke, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды