Mercury 135 Verado FourStroke Скачать руководство пользователя страница 9

Страница: 9 / 123

Maintenance

Cleaning Care Recommendations.................................................................... 60

EPA Emissions Regulations............................................................................. 62

Inspection and Maintenance Schedule............................................................. 63

Flushing the Cooling System............................................................................ 64

Top Cowl Removal and Installation.................................................................. 65

Battery Inspection ............................................................................................ 65

Verado Engine Battery Specifications.............................................................. 66

Air Filter............................................................................................................ 67

Fuel System...................................................................................................... 71

Corrosion Control Anode.................................................................................. 74

Propeller Replacement..................................................................................... 75

Spark Plug Inspection and Replacement..........................................................77

Fuses................................................................................................................ 81

Steering Link Rod Fasteners............................................................................ 82

DTS Wiring System.......................................................................................... 83

Accessory Drive Belt Inspection....................................................................... 83

Lubrication Points............................................................................................. 83

Checking Power Trim Fluid...............................................................................86

Checking Power Steering Fluid........................................................................ 87

Changing Engine Oil......................................................................................... 88

Gearcase Lubrication........................................................................................91

Storage

Storage Preparation..........................................................................................94

Protecting External Outboard Components...................................................... 94

Protecting Internal Engine Components........................................................... 95

Gearcase.......................................................................................................... 95

Positioning Outboard for Storage..................................................................... 95

Battery Storage................................................................................................. 95

Troubleshooting

Starter Motor Will Not Crank the Engine...........................................................96

Engine Will Not Start.........................................................................................96

Engine Starts But Will Not Shift Into Gear........................................................ 96

Engine Runs Erratically.................................................................................... 96

Performance Loss.............................................................................................97

Battery Will Not Hold Charge............................................................................ 97

eng

vii

Содержание 135 Verado FourStroke




























































































































Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды

Mercury 135 Verado FourStroke, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 135 Verado FourStroke

Отзывы:

Похожие инструкции для 135 Verado FourStroke

Бренды по названию

Популярные бренды